22 October, 2014

Adding a mp3 headset to a 3M hearing protection


If you are lucky enough to work in a factory with the times, surely ye be required to wear helmets as a image.

The workshop music rarely it gets, and even went down, between the noise and helmets could barely hear, but ... what if we add a mp3 to helmets?

Use this idea with responsibility; if you put loud music, maybe you do not hear a fellow warning danger.
A friend had the bright idea to do it, and here is the result.

Get professional photos on your Android phone with HDR Camera

When we get a picture with a camera either, and there is a great contrast of light from one area to another, or out overexposed photo if we get all the details of the dark side (in the photo below, the reflections in the cups): 

Image Gallaxy S SCL focusing the dark side of the glasses

Or the details of the shaded areas are lost, when we focus on the brighter side, as shown in the following image:

Galaxy S SCL image focusing the white part of the vessels
(This document was translated using Google Translator from the original spanish article)

Installing the USB driver for Arduino Leonardo in Windows 7 32-bit

The open source electronic board Arduino Leonardo
Yesterday I could try an electronic board that will accompany me for a long time in all my projects; the open source electronic board Arduino (Leonardo model with more inputs / outputs). 
This plate, if you like the "Do It Yourself" is impressive: 
  • Cheap (from 20 €)
  • Modern, comprehensive and flexible, with 20-pin I / O for highly complex projects
  • Open Hardware and Software (no secrets, you can make yourself the pieces)
  • Easy to program (using high-level language based on Processing )
  • With many examples and an ever larger community
  • Very economical and complete, Have I said it yet? XD
If you want to know more about how was this wonder of electronics, nothing better than "Arduino The Documentary" . A demonstration of the power of open source and collaborative altruism: 



Let's go to the topic ... It cost me a lot to find how to install the USB driver for Windows 7 32-bit; I could'nt get it to work, did not find it, despite following the official guide . 

21 October, 2014

How to Install Windows 7 on a Compaq NC8430

Today we are going to install the best current Windows; 7, in this somewhat dated computer but with a Centrino Duo that can cope with the Win7. I've found that does not have the drivers for the hard drive, so I had to go to the manufacturer's website, HP, and download the AHCI Sata hard disk controller. 
To copy it to a USB need to burn it to a floppy, and as I don't have this anymore, I have had to do with a virtual floppy using an USB pendrive. 

What to do if you drop your mobile into water

First, stay calm and act quickly, take it out of the water and remove the battery, the chances of recovering a long time is decreased if the battery; internal short circuit could be damaging and irrecoverable watching it later.

Then it is best to disarm as much as possible (there are numerous online manuals how to disarm the different terminals) and give heat with a hair, but not too hot as to melt XD.
If you act fast, you will probably only get wet surface. Remove the battery, and if you see it completely dry inside, you can dry it with a hairdryer. You were lucky this time! XD
(This document was translated using Google Translator from the original spanish article)

Once disarmed (without battery or SIM and memory card and lost everything you can) you can opt for the easy solution, which gives a result most of the time, which is putting it in a closed rice for several days container, at least one week if you have not disarmed lot, or at least 3 days if you separate all the pieces, until it is dry. Rice is the desiccant (moisture absorbing) cheaper there. 

02 May, 2011

Stainless steel biomass heater produced in-house - by Jose

Update: If you wanna make this project on your own, I advise you to not put the horizontal steel sheets to avoid problems with smoke; those sheets cool down the fumes a lot and it is bad for verting, the tar and slag will stick to the tube. To avoid this situation the temperatures of the smokes must be over 300ºC.
If the tube is long, we have to put an insulated tube to maintain the ignition temperature inside of it.

This entry I will devote to the project of Jose, who kindly sent me photos and details of his proposed home in stainless steel boiler., As I am concerned by the crisis and the environment. Hope you enjoy it as much as me.
Project Details


Photo of the stove in operation in the absence of cover with drywall

(This document was translated using Google Translator from the original spanish article

Jose, another hands of Toledo has developed a wood boiler full of stainless steel., And assures us that is like a shot, in 10 minutes take the set temperature 60 degrees and starts pumping, the house is large (210m) and 2h hot. Is supercontento, of which I am very happy because it saves money and uses renewable energy such as wood (= 0 Co2) and get some exercise step carrying firewood (with saving him from the gym ;-).
Started commenting on this post , in which he commented that before light was paying € 500 every two months using a heat pump, while the neighbors, heat radiators "blue" spent € 600! per month, an entire salary.

Advantages of biomass
There will be people who think "gas is the most comfortable, give it to the thermostat and forget." And it is true, only that the discomfort comes from the ax € 150 per month, money that goes out of Spain, in addition to increasing climate change.
Wood waste helps the local economy, providing jobs in the collection, cleaning and transporting forest biomass.
Besides these stoves, wood metiéndoles good, they just need loads every 3 or 4 hours, about 15 kg. can heat up a house of 100 square meters, and is a good exercise to eliminate the daily stress, thereby relaxing the contemplation of the fire!

Heat the house with the stove: Place a coil in a Hergóm stove

The stainless steel coil and placed

(This document was translated using Google Translator from the original spanish article
Last weekend a friend and I were staying with a friend in Lazagurría . It is a small and intimate, you saw the south of a hill cottages, most over 50, who has managed to survive the decline of population on little towns on Spain (20 km to he city Logroño).
Noa, an impressive skillful woman, intending to heat the house with the fire of the plate in the kitchen, she wanted to better distribute the heat for the house of your old wood stove and saw on my blog, and in the end we put a coil efficiently adapted to your kitchen, with which it heats the radiators. Cost of the modification: 100 € and 200 € coil installed accessories for it.
We have made very good impression, we have been so pleased with their hospitality to revisit more often ;-). (Will accept requests from the entire peninsula, see the email in the top-right of the blog: D).
The kitchen is typical Hergóm still present in many old houses of Spain, which gives considerable heat and uses very good wood for their manufacture refractory brick and reinforced molten metal.

In Hergóm still making this type of cuisine, with more modern lines:

Adapt an electric water heater for use as heat storage by adding a coil

Copper coil to heat household water tank
(This document was translated using Google Translator from the original spanish article)

Install a system for using solar energy or biomass to produce hot water in winter is profitable within a few years (particularly in areas where solar power is not enough), but can be very expensive for many, especially in developing countries.
With this tutorial you intend to use an old water heater 200 liters. of 'Cointra' brand and add a coil to heat the water inside. Quite a challenge considering we have to keep the seal and put it in without enlarging the tank ;-)-.
Before deciding on this, I had several options for heating water for hot water in a simple and economical, each with its pros and cons:

  • Buy me a plate heat exchanger high performance to bring the heat to the tank. This solution has many drawbacks, it affects the lime, is expensive (between 60 and 300 euros), you need a second engine to circulate the water tank (thereby generating mousse) and if you want to give priority to the ACS have to put a three-way motorized valve to divert excess heat after reaching a certain water temperature.


A copper heat exchanger standard.

25 September, 2009

Preparation of a stainless steel coil for the Russian stove


(This document was generated using Google Translator and then correcting some errors from the original spanish article).


Recently I showed you how to get better performance from a wood stove, using a Masonry Heater.
Yet I realized I could get even more performance (the accumulator design is not very efficient), and could benefit even more from the heat from the flames by adding a similar coil placed on the other stove my parents to recover more heat for other uses.

Underfloor heating
Hopefully, this floor was rebuilt in 2003 I had the great idea of putting underfloor home heating.


(of which I only keep this photo) made with copper pipes covered with dough and small amount of cement to make it loose and allow expansion of the tubes.
The technique of using the floor instead of radiators is the best way to heat your home for several reasons:
  • Being a greater heat-emitting surface the water temperature can be much lower so the energy efficency  is between 15 and 20% higher than with other systems.
  • By the same reason, solar energy systems can be used to transfer heat energy from the sun roof to the rooms of the house, for its performance at low temperatures (around 20 to 40 º C).
  • The comfort is higher, since heat is evenly distributed and from the bottom up ... it is a pleasure going barefoot with the flagstones at 25 º C! Soil is also the heat accumulator, thus heating it for several days, we will be warmed up for two days.
  • We eliminated the pesky radiators, usually placed next to windows covered with curtains so the losses through the glass are accentuated. All this is avoided.
  • When working at low temperatures we can use cheaper plastic materials and is often used PE.
The disadvantages of this system are almost nonexistent. It may be mentioned that requires more work and labor (if done at the moment of building the house could be even cheaper) and that if there is a leak it is difficult to repair (could involve a large surface lift) and it is inappropriate to use soil with low transmission of heat as wood.

On my system I should have isolated the soil below the radiant tube, since underneath is the rock of the mountain to which is transmitted 30% of the heat and taking longer to reach temperature. The good thing about this is that if the soil is heated to 40º C (which requires several loads of wood in the stove), the soil will remain hot for 24 hours ;-).

07 March, 2009

Heat accumulator: Increase the performance of the wood stove (Russian Stove or Masonry Heater)


In this post we will see how to get more performance from a wood stove smoke passing through a vertical loop firebricks and do not involve maintenance.

Recently, 
I spoke of the "Russian stove" , which is simply a low heat oven or built with bricksrefractory and gives a great performance and comfort for heating. 

However I made ​​the mistake of assuming that the narrow passage I left still allow the passage of smoke (considering 4 meters in fire that made ​​shooting), but the smoke is cooled much and slowed both passing the shot was almost zero,introducing a lot of smoke in the room every time the door would have and it was very difficult to remove.
So since I had to disassemble the entire block bricks, took the opportunity to completely change the design because putting cast iron stove out from the wall it was a botched it had more disadvantages than advantages; this time the put-in wall, and on it, the heat accumulator block smoke, leaning against the wall by an arch .
I've always liked the brush fires; when I was little I was soup on the couch in front of the fire in my parents' house; careful with the crackle of firewood and comforting warmth, causes drowsiness;-).
I learned from the mistakes of the previous experiment, with the new design and I hope to have more advantages:
  • Avoiding the maintenance, with a simple circuit favoring vertical soot fall within the same range.
  • Better take advantage of the space and the brick is flush with the wall, plus it is prettier.
  • Increase the shot, making a larger even than the smoke outlet of the stove step, which prevents the smoke comes out of the great door of the stove I have chosen.
  • By using more bricks to the accumulator increases the stored heat and hours of comfort.
The only downside is that its performance is reduced by 10% (not recessed stove so easily and quickly releases the heat), heat up more slowly home. Still, a daily charge burning temperature sufficient to maintain at 18 ° C with 7th outside.

The nice thing is big refractory bricks which are highly resistant to shock, so I could disarm them,removing the refractory mortar with a pickaxe or hammer. It took me six hours to clean every drop and a Chinese work.



After placing the stove in place and discussing how to support the brick arch, I saw that I couldput bricks in the space between the concrete wall and the stove, so I have decided to support the weight distributed between the bricks and wall, to minimize the cut to be made ​​in the wall.





To the right I have chosen to put two vertical bricks instead of lying, and I think it will be well placed enough to support the weight and stress.


More mass must be put on top of the curve to be doing. It is better and stronger if purchased or prepared bricks wider on one side than the other, but it takes more money or work.


To hold the bricks as you would have used by placing pieces of brick. It would have been much better if he had made ​​a wooden template which then could remove, but I hoped to do guesswork and has been my right hand a little fall lr. so there is a lag of one centimeter. Although it has not been so bad for the first time I do one.



Attention: In my case this solution is suitable for the wall on which rest the 250 kg.Brick is solid concrete and stone. If you want to do the same and the wall is brick,build good columns on both sides with refractory bricks lying, supporting the arch in them.

The part of the center, with the mouth of the chimney is the most difficult, leave the hole but putting bricks wide as possible for resistance to the whole arc. Then the weight of the bricks will go around the center, so I'm not worried that the area can support less weight.


A note: It would have been stronger still mixing short and long bricks to prevent the continuation of the line of cement in the binding of both rows, as has been weaker for that part.


Do not forget to place fiberglass or rock wool (an insulating support that high temperatures) in the gaps left between the flue outlet of the stove and bricks.

We hope one day it has begun to harden the dough and we can lay bricks until a flat base, with bricks cut in half to reduce the use of mortar as possible.


We're raising the tower, laying bricks in the path of smoke, forcing him to go out and toward the center, so that the entire block into contact with the heat of the smoke, yes, always keeping the minimum smoke evacuation step.


I have been very conscious step to do so sufficiently to favor the natural fall of excess sootinto the mouth vent the stove itself. This way I avoid having to put records accessible for cleaning.Although there is also the possibility of getting dirty enough to stop smoke freely, I think it will take several years and can always drop the last row of bricks for cleaning.



The width of the passage for the smoke I have left is greater than before; but does not have to be excessive, the bricks must go coil supported at least two centimeters; heat may crack but between the weight of the other and mortar will not fall.


You have to leave a little space between the wall and the bricks that allow them to cool and heat the room, an inch is enough. I have not stopped and the heat is not released from the bricks so easily, making it less efficient.
Furthermore, in the mortar spare not used; it is important that there are no gaps where the smoke escape. You can always pick up the remains after the palette. It is also important not to leave any meeting without mortar and use a rubber mallet to set them right.


Finally arriving at the fire escape, I closed with big old bricks, using fiberglass to seal the gapsbetween the pipe and the bricks.
In this post I have not repeated some of the advice given or information on the Russian stove, I invite you to also read the above for more information.



Between the stove and the arch is a hole through which emits a lot of heat and partially shut, putting a grill with holes for the top. Keep in mind that the metal expands more than the mortar or refractory brick, so that should not be put between the stove and bricks.

Try to remove all that is between the stove and let the bricks to dilate freely.

And in this video you can see how it works; shoots much better and use is practically the same. I do not he could have ended at a better time: is back to snow in my area.
I hope that it do not give me any more problems for many years.




Ya just need to finish placing firebricks around beautify and clean them. Probably take the heat of this stove and to heat the water, but that later ...

What has been good to me, and how proud one is left watching your project and illusion performed, priceless!

Greetings to all and see you soon! Suggestions and comments are allowed, do not be shy!

Related links:
Russian stove in Bioclimatic Architecture blog (very good page on sustainable architecture)
Manual for the manufacture of a Russian stove - ( source )
"As a Russian stove is manufactured" on Forosolar of SolarWeb.net
Stoves high performance or "Kachelofen" in the German wikipedia ( translated into Spanish )
Masonry Heater in North America