The plotter fails to recognize the cartridge: Repairing a 500-800 HP Designjet 42 "

We had a problem with our plotter; it marked "unrecognized cartridge" error before finishing of each printed plan; when we repositioned the cartridge the problem was solved for a while, but it seemed a problem of poor contact with the cartridge chip (it was produced when the motor axis ink supply was activated).

To repair it, you have to access the module cartridges; first of all we need to remove the cover of Control, it is a matter of finding and removing all the screws, simple task and which information is on the internet, so that I refrain from commenting;)

Turn off RadioCD in a Xsara Picasso car: Connection to the burner

We dropped the front screws and side to find the lighter wiring

RadioCD included by factory in the Citroen Xsara Picasso does not disconnected immediately after removing the key, so remains on a couple of minutes after the unit is disconnected.

In this case it is advisable to connect the red wire RadioCD "ON" (not the one going to the battery, but the activator) to positive cable of the burner, and then this hassle is avoided.

In Depth: Lexman 9W LED bulb E27 230V 4000K 806 lm of Leroy Merlin

In my case gets 3 years warranty

LED bulbs are already flooding the domestic market, with options for almost every need.

We will analyze in detail a model that sells E27 Leroy Merlin with 3 years warranty brand Lexman  (non-publicizing, just to compare).

This bulb shines very well, with a more than acceptable theoretical efficiency of  90 lumens/W, perfect for replacing incandescent bulbs of 100W  (tested). 

His tone, a clear yellowish 4000º Kelvin, is suitable for everywhere in the house (although it is away from 5600K natural sunlight, colder), and a higher CRI of 80, enough.

If we break the glass we see that the controller gives 94V, feeding 33 LEDS 3528 series (which theoretically receive 2,84V and 0,27W each emitting 24 lm / ud), giving 806 lumens and 9W according to manufacturer (and although I can not measure it, seems to be true from its luminance):

The design to dissipate heat is of lightweight aluminum inside, which contacts the exterior part thermal plastic, that transfer worse the heat than aluminum, so it does not burn and can be touched, but it would be best if it were metal body such as lamps from Ikea, since the chip area after 6 minutes is at 43 ° C with 18ºC environment temp.:

With the (+ - 1 ° C) temperature sensor check infrared LEDs

and reaching 64 ° C! after half an hour, a temperature not very convenient for semiconductors. The manufacturer indicates a lifespan of 15,000 hours, but I hardly trust it, I recommend saving the invoice and not buying this bulbs because, if we use a lot, It will not reach the three years guaranteed!

Anyway, for € 6 per bulb, and for environments such as the bathroom where they are at most one hour on, they are more than recommended. For other uses, best to get better quality lamps.

Preparing a ventilated protective mask for Airsoft

Homemade ventilation mask

Eye protection is mandatory in airsoft, but most masks do not have enough ventilation, so you end up with very low vision by condensation on the policarbonate plastic.

As others have done before me, the trick is to introduce fresh air with a small fan and battery; I used a fan from a notebook computer, with a small switch and a 18650 lithium battery (4.2V) in the corresponding adapter .

Repairing an old Mitutoyo profilometer probe

Some time ago I repaired an old Mitutoyo profilometer 178-928D , which no longer has spares and which had broken the pin that transmits motion to the head holder; a calibrated shaft that moves left and right and which I hold in the following image (the pin / screw was in the center hole):

This probe has a very simple operation. The spindle that is coupled detects changes in a very similar way that is translated the marks in an old LP music disk, transmiting the movements caused by the roughness by a magnet and coil needle.

The shaft that moves the spindle is moved in a controlled manner with a step by step motor to an endless spindle, first the engine slowly forward in the measurement phase, and then quickly picking head to its starting position, all controlled from the profilometer which is connected with a cable with 6 wires (that is a seven or eight cable, but one or two are not used, as you can see in the following images after repairing the cable too):

Repairing a tape backup LTO 2 unit: HP Ultrium 448 with broken tape

In a unit Ultrium Fujitsu (HP) for backup, the tape had broken, being useless as the mechanism for capturing the tape was inside it. To repair the unit is complicated, recommended only to those who have already dealt above with similar mechanisms (VHS, glory times). 
To repair it is necessary to understand the method these units use (and many other models are based on the same principle), a curious way to save space by having a single drum in the cartridge and in the unit, where the tape passes from one side to another as information is stored, until it ends.

These LTO (Linear Tape Open) are optimized for capacity, and the latest versions, able to store 2.5TB of information in one cartridge that costs about 20 €, making it very competitive in terms of price and space currently.

After this brief introduction, let's go to the subject.

6 tips to save on your vehicle maintenance

Today, thanks to the internet we have plenty of advices and hints to save maintaining our vehicle, we have plenty of tutorials for whom are a little handyman; from changing lamps, brushes, etc to oil changes, and some dare to change pads and cushions. After years of use with my Xsara Picasso, I share with you the ideas and optimizations that can be applied to your vehicle to save money, helping the nature too.

1. Change the rubber instead of the entire windshield wiper

Change only the rubber and be ecofriendly

Repairing and Adflo Speedglas battery ref 837621 with LI-ION 4.2V Cells

Lately I have been repairing multiple wireless devices whose NI-MH batteries have deteriorated ; usually get considerably cheaper make you the battery pack with a new charger is to buy it new; in this tutorial I will show how to build a battery of 4500 mAh 12.6V and 3 packs of 3 cell li-ion parallel each to replace a battery 10.8V and 4000 mAh NI-MH (9 batteries in series 1.2V) with just 32 € (charger not included).

Update: I uploaded how I repair them to youtube:

HD version

And slim version.

LITHIUM battery types depending on their composition

The Lithium-ION technology has improved a lot as  the advantages of having no memory effect and higher energy density per kilogram than any other current technology , we can add that  depending on the type of materials used , allows different power / energy densities; we can have instantaneous powers from 1C (2A / time to a cell 2000 mAh) of the LI-Cobalt portable typical 5C of manganese (LiNiMnCoO2) or 15C for the past employed in Automobiles (LiNiCoAlO2) or 30C with LiFePO4 .

Modifying an airsoft HK 416 UMAREX with 11,1V for increased rate of fire: from 13 bps to 18 bps

HK 416 from UMAREX, very high quality materials and precision

Recently I personalized with more cadence one airsoft replica HK 416 from UMAREX, the best available today replica of the lethal original, getting to shoot 18 balls per second instead of 13 with the recommended battery.

For this we have got 11,1V instead of the 7.4V li-ion recommended by the manufacturer, using 6 standard size batteries 2000 mAh 18650 and 1C discharge . Usually LiPo is more desirable for these cases, for the effort that must hold the batteries, they probably will last less than normal ... but what can we do... life is short;) and we just had them available.

Putting 11,1V to the repeater you are breaking the guarantee, but it have such good material and design that we'd rather risk getting a machine of epic massacres;)

In the following video a Youtube friend did the same and is working very well:

How works an electric cooler: Cell peltier

We pack a cooler for the curious

Well, after a temporadilla almost no entries, I think this summer will not you going to complain;.)We'll start with this entry, in which he disarmed a cooler of those that plug into the car (or home if you adapt one transformer least 5 amps and 12 volts), to discover another fascinating use of semiconductors (thermoelectric effect) and electricity: The Peltier cells .